|Technology||Silica membrane and silica matrix|
|Starting material||Filter, water|
|Format||XS spin columns|
|Fragment size||100 bp–approximately 50 kb|
|Elution volume||100 µl|
|Preparation time||<70 min (excluding water filtration)|
- Product finder
- Plasmid purification
- Genomic DNA purification
- DNA/RNA cleanup and extraction
- Parallel DNA, RNA & protein
- Automated DNA and RNA purification
- RNA purification
- Nucleic acid purification accessories
- NucleoMag DNA Microbiome
- NucleoMag DNA Bacteria
- NucleoSpin Plant II
- NucleoSpin RNA Plant and Fungi
- NucleoMag DNA Food
- NucleoSpin DNA Insect
- NucleoSpin Soil
- NucleoSpin 8/96 Soil
- NucleoBond RNA Soil
- NucleoSpin DNA Lipid Tissue
- NucleoSpin DNA Stool
- NucleoSpin RNA Stool
- NucleoSpin Microbial DNA
- NucleoMag DNA/RNA Water
- NucleoSpin eDNA Water
- NucleoSpin 96 DNA Stool
Rapid purification of environmental DNA from diverse water samples
The NucleoSpin eDNA Water kit enables rapid and reliable purification of environmental DNA (eDNA) from diverse water samples. The kit incorporates silica-matrix and silica-membrane technologies to allow for isolation of high-quality DNA from filters in about an hour, avoiding the long, overnight incubation steps typical of eDNA workflows. Columns included in the kit are treated with ethylene oxide in order to minimize the risk of DNA contamination, and the protocol is compatible with a variety of filters and filtration systems, including conventional bottletop round filters (e.g., 45 mm) as well as cartridge filters (e.g., Sterivex). In addition, an alternative protocol that circumvents filtration by enabling direct eDNA precipitation is provided. As demonstrated below, these properties make NucleoSpin eDNA Water an ideal solution for analyses of both freshwater and saltwater ecosystems with varying levels of organic and inorganic matter.
- Fastest workflow among eDNA kits currently on the market—pure eDNA in hours instead of days
- Ethylene oxide-treated XS silica membrane columns—minimized risk of DNA contamination
- Compatible with diverse types of water, filtration systems, and laboratory setups
Sample preparation workflow for NucleoSpin eDNA Water. Samples can be obtained either by filtration with round filters or filter cartridges (e.g., Sterivex). DNA is liberated from the filter by a strong lysis buffer. Alternatively, eDNA can be precipitated from <40 ml of unfiltered water (using Buffer PREC, Cat. # 740568). NucleoTrap Suspension beads efficiently bind the DNA while minimizing carryover of contaminants. Following washing and drying steps, the bead suspension is transferred to a NucleoSpin XS column, from which pure eDNA is eluted. The purification steps take less than 70 min, while total preparation times vary depending on the sampling and/or filtration setup.
Compatibility with different filters and filtration systems
Consistent performance with diverse round filters. 500-ml samples of creek water were filtered through the following different types of round filters, which were then processed using NucleoSpin eDNA Water: regenerated cellulose (RC), cellulose nitrate (NC), cellulose acetate (CA), polyester (PE), polycarbonate (PC), mixed cellulose ester (CM), and paper. As demonstrated by the resulting Ct values obtained in a downstream qPCR analysis, performance of DNA isolation was similar for each of the filter types and comparable to the performance observed with the recommended ethylene oxide-treated glass fiber filter (GF), which provides the best flow rate and lowest risk of clogging.
Compatibility with different water filtration systems. Samples of creek water were filtered through a glass fiber filter (GF) as well as several filtration systems commonly used in conjunction with eDNA purification. The NucleoSpin eDNA Water kit was then used to purify eDNA from each filter unit, and eluates were analyzed by qPCR for metazoan DNA. Purification from each filtration system yielded comparable results, as demonstrated by the consistent Ct values.
Superior downstream performance as compared to competitor kits. eDNA was purified from running water (creek) and static water (pond) using the NucleoSpin eDNA Water kit in parallel with two competitor kits (“BT” and “PW”) and analyzed by qPCR for metazoan DNA. As demonstrated by the lower Ct values, NucleoSpin eDNA Water provided higher sensitivity than the competitors for both sample types.
Takara Bio USA, Inc.
United States/Canada: +1.800.662.2566 • Asia Pacific: +1.650.919.7300 • Europe: +33.(0)1.3904.6880 • Japan: +81.(0)77.565.6999
FOR RESEARCH USE ONLY. NOT FOR USE IN DIAGNOSTIC PROCEDURES. © 2021 Takara Bio Inc. All Rights Reserved. All trademarks are the property of Takara Bio Inc. or its affiliate(s) in the U.S. and/or other countries or their respective owners. Certain trademarks may not be registered in all jurisdictions. Additional product, intellectual property, and restricted use information is available at takarabio.com.